Nortek Security and Control KB
Hubmax Hardware Articles RSS Feed
How do I configure my SEG-1 or my SEG-M to use a static IP address or to configure it as a Dynamic (DHCP) type device?
Viewed 4835 times since Fri, Mar 12, 2010
Requirements: SEG-M or SEG-1 SEG-M is powered by the Max2 or Max3 panel SEG-1 requires 12VDC power supply Gateway Config Adapter (P/N 207-6000) IEI supplied, tan Phone Type Cord. Unused Com Port For PCs without a built in or free Com Port, a USB to... Read More
How do I setup communications between my Pc and my Max3/MiniMax3?
Viewed 4030 times since Mon, Mar 15, 2010
Scenario 1 Using the optional IEI USB to Serial Converter on Single Gang Plate (P/N 0295097) Connect the USB cable to any USB port on your computer. Connect the other end of the USB cable to the IEI USB to Serial Converter on a Single Gang Plate... Read More
I have added card users in HubManager Pro for my Max3/MiniMax3 but they do not work.
Viewed 3950 times since Tue, Mar 16, 2010
Perform the following troubleshooting steps: Check the wiring from the card reader to the front end connector on the Max3 panel. The proper wiring is: Card Reader ------ Front End Black Black Red Red Green WH/BK or D0 White... Read More
How do I setup communications between my PC and my Max2/MiniMax2?
Viewed 3442 times since Fri, Mar 19, 2010
Scenario 1 The PC is less than 6' from the Panel and using the included PC Software Assembly Kit (P/N 2085010) Connect the IEI -supplied ToComp (P/N E000-0004) Adapter to the Communications Port (Com Port) on your computer. Connect the IEI... Read More
How do I use my Enrollment Station?
Viewed 3204 times since Tue, Mar 30, 2010
The Enrollment Station is a device used to enroll HID format proximity cards (up to 40 bits). This device connects to the PC using a USB or serial COM port connection. It allows you to read the raw data card directly from an HID proximity card and... Read More
How do I setup communications between my PC and ProxPadPlus?
Viewed 2648 times since Mon, Mar 22, 2010
Scenario 1-Using the optional IEI USB to Serial Converter on Single Gang Plate (P/N 0295097) Connect the USB cable to any USB port on your computer. Connect the other end of the USB cable to the USB to Serial Converter on Single Gang Plate. ... Read More
How do I setup communications between my PC and an HC500P?
Viewed 2311 times since Thu, Mar 11, 2010
How do I setup communications between my PC and an HC500P?Scenario 1-Using the PC Software Assembly Kit (P/N 2085010) Connect theToComp (P/N E000-0004) adapter to the Communications Port (Com Port) on your computer. Connect the included phone... Read More
What type of battery backup do I need for my IEI product?
Viewed 2097 times since Tue, Mar 30, 2010
If you need to setup a backup power supply in the event of a power failure you will need to know the total Milliamps the unit is drawing. The total milliamps for the IEI products can be found on the installation documentation packaged with the... Read More
HID 5355KP
Viewed 2021 times since Thu, Dec 8, 2011
HID 5355KP: PROGRAMMING CODE + PIN TO WORK WITH THE MAX 3 This is a bit burst keypad that is not buffered which is required by the Max 3. ADI stocks the 00 format. An HID tech will need to send a free programming card to change the format... Read More
How do I number my doors?
Viewed 941 times since Tue, Feb 3, 2015
If you have a PROXPAD PLUS each unit in the 485 connection needs to be given a door number: At the ProxPadPlus get into programming by pressing 99 # master code *.  By default your master code is 1234.  A blinking yellow light indicates the... Read More